X-Git-Url: https://git.rrq.au/?a=blobdiff_plain;f=rrqnet.8.adoc;h=f2159fb7ebf247ffe0a83fd4a5ddf2464c7a2f44;hb=caabee3251dd013f0fa4566ef98136540a3e9761;hp=5afd0d8ed5800a85b65878f69f997a02a2bc47e1;hpb=73affd501975e86bf4ab9b4850f5d483c598b417;p=rrq%2Frrqnet.git

diff --git a/rrqnet.8.adoc b/rrqnet.8.adoc
index 5afd0d8..f2159fb 100644
--- a/rrqnet.8.adoc
+++ b/rrqnet.8.adoc
@@ -117,14 +117,14 @@ Ethernet switch that provides connectivity among its +UDP+ channels
 without involving the host network other than for the tunneling.
 
 
-REMOTE DECLARTIONS
-~~~~~~~~~~~~~~~~~~
+REMOTE DECLARATIONS
+~~~~~~~~~~~~~~~~~~~
 
 .ipv4 address block
 
 This format declares remotes by +ipv4+ address, with optional network
 prefix length (0-32), optional port (1-65535) and/or optional key file
-pathname. *updtap* will accept packets from sources that match. If the
+pathname. *rrqnet* will accept packets from sources that match. If the
 network prefix length, +n+, is omitted or given as 32, and a port is
 given, then the remote is taken as an _uplink_.
 
@@ -139,7 +139,7 @@ given, then the remote is taken as an _uplink_.
 .plain ipv6 address block
 
 This format declares remotes by ipv6 address, with optional network
-prefix length (0-128) and/or optional key file pathname. *updtap* will
+prefix length (0-128) and/or optional key file pathname. *rrqnet* will
 accept packets from sources that match. This format (without square
 brackets) is without port number part, and it thus only declares a
 prefix mask for allowed sender hosts.
@@ -148,7 +148,7 @@ prefix mask for allowed sender hosts.
 
 This format declares remotes by ipv6 address, with optional network
 prefix length (0-128) within square brackets, then optionally a port
-number and/or an optional key file pathname. *updtap* will accept
+number and/or an optional key file pathname. *rrqnet* will accept
 packets from sources that match. If the network prefix length, +n+, is
 omitted, or given as 128, and a port number is given, then it declares
 an _uplink_.
@@ -371,7 +371,7 @@ than a tap for local network traffic. This operation mode has some
 rare use cases, such as linking two *rrqnet* daemons, or connecting to
 a VDE network. For example:
 
-.stdio network between two updtap plugs
+.stdio network between two rrqnet plugs
 ====
 ----
 # dpipe rrqnet 1400 0.0.0.0/0=keyfile0 = rrqnet 1401 0.0.0.0/0=keyfile1 &
@@ -409,16 +409,14 @@ communication.
 
 *rrqnet* bridges its connections, and forwards Ethernet broadcasts to
 all known end-points except the incoming one. The input logic takes
-care of avoiding broadcast cycles. Still, the safe advice is that one
-should avoid a cyclic *rrqnet* set up except for single-hop cliques of
-host groups.
+care of avoiding broadcast cycles.
 
-*rrqnet* does not have any Spanning Tree Logic (STL), but only some
-simple timing logic based on binding MAC addresses to remotes. That
-binding is sticky for a short time: 6s for broadcast and 20s for
-unicast. Any packet received during that time from the same MAC
-address via another remote is dropped. Also, a downlink without
-incoming traffic for 3 minutes is considered stale.
+*rrqnet* does not have Spanning Tree Logic (STL), but some simple
+timing logic based on binding MAC addresses to remotes. That binding
+is sticky for a short time: 6s for broadcast and 20s for unicast. Any
+packet received during that time from the same MAC address via another
+remote is dropped. Also, a downlink without incoming traffic for 3
+minutes is considered stale.
 
 *rrqnet* sends a "heartbeat" of an empty UDP message on its uplinks
 every 30 seconds. This is done in order to maintain the channel with
@@ -435,8 +433,6 @@ SEE ALSO
 --------
 *rrqnet-cron.sh(8)* - Management script to uphold a *rrqnet* plug.
 
-*udptun(8)* - Packet tunneling over UDP.
-
 *vde_plug(1)* - Virtual Distributed Ethernet plug.
 
 AUTHOR